In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed N-Gauge Overhead Line Equipment 2 x Registration Arms LEFT HAND for SERIES 2 - Two Track Cantilever type OHLESET E10-3 - product code 2WH0901003REGISTRATION ARMS only - PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWDetailed N-Gauge Overhead Line Equipment 2 x Registration Arms LEFT HAND for SERIES 2 - Two Track Cantilever type OHLEPLEASE READ THE FULL PRODUCT DESCRIPTION BELOWN Gauge SET E10-3 - product code 2WH0901003
This set E10-3 includes TWO (2) Left Handed Registration Arms that are intended for fitting to the SERIES 2 - Two Track Cantilever kits (SETs E10-1 and E10-2).PLEASE NOTE that these registration arms are NOT intended to support the fitting of contact wires.
Other types of registration arms for the SERIES 2 - Two Track Cantilever OHLE are available as follows:-
SET E10-4 Right Hand Registration Arm (Series 2)
SET E10-5 Left Hand Registration Arm (SERIES 2 magnetic type to allow fitting of Peco type OHL wires) note [wires are not included]
SET E10-6 Right Hand Registration Arm (SERIES 2 magnetic type to allow fitting of Peco type OHL wires) note [wires are not included]
All parts are supplied unpainted; before painting it is recommended to apply a light coat of primer.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed N-Gauge Overhead Line Equipment 2 x Registration Arms RIGHT HAND for SERIES 2 - Two Track Cantilever type OHLESET E10-4 - product code 2WH0901004REGISTRATION ARMS only - PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWDetailed N-Gauge Overhead Line Equipment 2 x Registration Arms RIGHT HAND for SERIES 2 - Two Track Cantilever type OHLEPLEASE READ THE FULL PRODUCT DESCRIPTION BELOWN Gauge SET E10-4 - product code 2WH0901004
This set E10-4 includes TWO (2) Left Handed Registration Arms that are intended for fitting to the SERIES 2 - Two Track Cantilever kits (SETs E10-1 and E10-2).PLEASE NOTE that these registration arms are NOT intended to support the fitting of contact wires.
Other types of registration arms for the SERIES 2 - Two Track Cantilever OHLE are available as follows:-
SET E10-3 Left Hand Registration Arm (Series 2)
SET E10-5 Left Hand Registration Arm (SERIES 2 magnetic type to allow fitting of Peco type OHL wires) note [wires are not included]
SET E10-6 Right Hand Registration Arm (SERIES 2 magnetic type to allow fitting of Peco type OHL wires) note [wires are not included]
All parts are supplied unpainted; before painting it is recommended to apply a light coat of primer.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed N-Gauge Overhead Line Equipment Mast Structure Kit - Mk1 Type A Structure Kit with 75mm Span for up to 2 Tracks, including Magnetic Bases
Typical of the style fitted on the West Coast Main Line.SET E11-1 - product code 2WH0901101PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWDetailed N-Gauge Overhead Line Equipment Portal Structure Kit - Mk1 Type A Structure Kit with 75mm Span for up to 2 Tracks, including Magnetic Bases
Typical of the style fitted on the West Coast Main Line.
PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWN Gauge SET E11-1 - product code 2WH0901101This set E11-1 includes parts to construct one (1) Mk1 Type A structure for up to 2 Tracks (2 Masts, 2 Bases and 1 Span section).
The two Pile Driven style Bases included in the kit come with magnets to fit into the bases and OHLE structure. The use of magnets allows the OHLE structures to be easily removed and re-fitted on your layout.PLEASE NOTE - the registration arms are NOT included and should be purchased separately.N-Gauge Registration Arm options for the Mk1 Style OHLE are available to Purchase Separately as follows:-
SET E11-5 - Mk1 Registration Arms and Catenary Wire Supports for Type A & B Structures (SET E11-5) - product code 2WH0901105
All parts are supplied unpainted; before painting it is recommended to apply a light coat of primer.Regarding the spacing of OHLE masts, the real railway mast spacing can be vary between about 20metres and 70metres which equates to 130 to 470mm in N Gauge. In general mast spacing is likely to be closer together at junctions and on sharper curves.OHLE Structure kit (SET E11-1) dimensions:-
Maximum height above baseboard (including base) - 65mm
Overall length of structure (across the tracks) - 91mm
Max width of structure/base - 8mm
Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed N-Gauge Overhead Line Equipment Mast Structure Kit - Mk1 Type B Structure Kit with Lattice Masts and a 75mm Span for up to 2 Tracks, including Magnetic Bases
Typical of the style fitted on the West Coast Main Line.SET E11-11 - product code 2WH0901111PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWDetailed N-Gauge Overhead Line Equipment Portal Structure Kit - Mk1 Type B Structure Kit with Lattice Masts and a 75mm Span for up to 2 Tracks, including Magnetic Bases
Typical of the style fitted on the West Coast Main Line.
PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWN Gauge SET E11-11 - product code 2WH0901111This set E11-11 includes parts to construct one (1) Mk1 Type A structure for up to 2 Tracks (2 Lattice Masts, 2 Bases and 1 Span section).
The two Pile Driven style Bases included in the kit come with magnets to fit into the bases and OHLE structure. The use of magnets allows the OHLE structures to be easily removed and re-fitted on your layout.PLEASE NOTE - the registration arms are NOT included and should be purchased separately.N-Gauge Registration Arm options for the Mk1 Style OHLE are available to Purchase Separately as follows:-
SET E11-5 - Mk1 Registration Arms and Catenary Wire Supports for Type A & B Structures (SET E11-5) - product code 2WH0901105
All parts are supplied unpainted; before painting it is recommended to apply a light coat of primer.Regarding the spacing of OHLE masts, the real railway mast spacing can be vary between about 20metres and 70metres which equates to 130 to 470mm in N Gauge. In general mast spacing is likely to be closer together at junctions and on sharper curves.OHLE Structure kit (SET E11-11) dimensions:-
Maximum height above baseboard (including base) - 65mm
Overall length of structure (across the tracks) - 91mm
Max width of structure/base - 8mm
Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed N-Gauge Overhead Line Equipment Mast Structure Kit - Mk1 Type B Structure Kit with Lattice Masts and a 135mm Span for up to 4 Tracks, including Magnetic Bases
Typical of the style fitted on the West Coast Main Line.SET E11-12 - product code 2WH0901112PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWDetailed N-Gauge Overhead Line Equipment Portal Structure Kit - Mk1 Type B Structure Kit with Lattice Masts and a 135mm Span for up to 4 Tracks, including Magnetic Bases
Typical of the style fitted on the West Coast Main Line.
PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWN Gauge SET E11-12 - product code 2WH0901112This set E11-12 includes parts to construct one (1) Mk1 Type B structure for up to 4 Tracks (2 Lattice Masts, 2 Bases and 1 Span section).
The two Pile Driven style Bases included in the kit come with magnets to fit into the bases and OHLE structure. The use of magnets allows the OHLE structures to be easily removed and re-fitted on your layout.PLEASE NOTE - the registration arms are NOT included and should be purchased separately.N-Gauge Registration Arm options for the Mk1 Style OHLE are available to Purchase Separately as follows:-
SET E11-5 - Mk1 Registration Arms and Catenary Wire Supports for Type A & B Structures (SET E11-5) - product code 2WH0901105
All parts are supplied unpainted; before painting it is recommended to apply a light coat of primer.Regarding the spacing of OHLE masts, the real railway mast spacing can be vary between about 20metres and 70metres which equates to 130 to 470mm in N Gauge. In general mast spacing is likely to be closer together at junctions and on sharper curves.OHLE Structure kit (SET E11-12) dimensions:-
Maximum height above baseboard (including base) - 65mm
Overall length of structure (across the tracks) - 149mm
Max width of structure/base - 8mm
Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed N-Gauge Overhead Line Equipment Mast Structure Kit - Mk1 Type A Structure Kit with 135mm Span for up to 4 Tracks, including Magnetic Bases
Typical of the style fitted on the West Coast Main Line.SET E11-2 - product code 2WH0901102PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWDetailed N-Gauge Overhead Line Equipment Portal Structure Kit - Mk1 Type A Structure Kit with 135mm Span for up to 4 Tracks, including Magnetic Bases
Typical of the style fitted on the West Coast Main Line.
PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWN Gauge SET E11-2 - product code 2WH0901102This set E11-2 includes parts to construct one (1) Mk1 Type A structure for up to 4 Tracks (2 Masts, 2 Bases and 1 Span section).
The two Pile Driven style Bases included in the kit come with magnets to fit into the bases and OHLE structure. The use of magnets allows the OHLE structures to be easily removed and re-fitted on your layout.PLEASE NOTE - the registration arms are NOT included and should be purchased separately.N-Gauge Registration Arm options for the Mk1 Style OHLE are available to Purchase Separately as follows:-
SET E11-5 - Mk1 Registration Arms and Catenary Wire Supports for Type A & B Structures (SET E11-5) - product code 2WH0901105
All parts are supplied unpainted; before painting it is recommended to apply a light coat of primer.Regarding the spacing of OHLE masts, the real railway mast spacing can be vary between about 20metres and 70metres which equates to 130 to 470mm in N Gauge. In general mast spacing is likely to be closer together at junctions and on sharper curves.OHLE Structure kit (SET E11-2) dimensions:-
Maximum height above baseboard (including base) - 65mm
Overall length of structure (across the tracks) - 149mm
Max width of structure/base - 8mm
Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed N-Gauge Overhead Line Equipment - Registration Arms and Catenary Wire Supports for Mk1 Type A or Type B Structures
Typical of the style fitted on the West Coast Main Line.SET E11-5 - product code 2WH0901105PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWDetailed N-Gauge Overhead Line Equipment - Registration Arms and Catenary Wire Supports for Mk1 Type A or Type B Structures
Typical of the style fitted on the West Coast Main Line.
PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWN Gauge SET E11-5 - product code 2WH0901105
This set is specifically designed to be used with our Mk1 OHLE structure kits E11-1, E11-2, E11-11 and E11-12 (not included).This set E11-5 includes the following parts:-
- Two (2) Registration Arms
- Two (2) Catenary Wire Supports
The parts are fitted to the side of the span of your assembled Mk1 OHLE Structure and may need to be attached with a very small spot of glue.
All parts are supplied unpainted; before painting it is recommended to apply a light coat of primer.Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed N-Gauge Overhead Line Equipment - Set of 6 Return Conductor Wire Supports for Mk1 Type A or Type B Structures
Typical of the style fitted on the West Coast Main Line.SET E11-6 - product code 2WH0901106PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWDetailed N-Gauge Overhead Line Equipment - Return Conductor Wire Supports (set of 6) for Mk1 Type A or Type B Structures
Typical of the style fitted on the West Coast Main Line.
PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWN Gauge SET E11-6 - product code 2WH0901106
This set is specifically designed to be used with our Mk1 OHLE structure kits E11-1, E11-2, E11-11 and E11-12 (not included).This set E11-6 includes the following parts:-
- Two (2) Single Span Side Mount Return Conductor Supports
- Two (2) Double Span Side Mount Return Conductor Supports
- Two (2) Mast End Mount Return Conductor Supports
The parts are fitted to the side of the span or end of the mast of your assembled Mk1 OHLE Structure and may need to be attached with a very small spot of glue.
All parts are supplied unpainted; before painting it is recommended to apply a light coat of primer.Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment Structure Kit – Mk1 25kV Type A Structure 2-Track structure,Typical of a type fitted to the West Coast Main Line route, incl. Magnetic Bases.PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWOO Gauge SET E16-1 - product code 4WH0901601Detailed Overhead Line Equipment Structure Kit – Mk1 25kV Type A Structure 2-Track structure, incl. Magnetic Bases, typical of a type fitted to the West Coast Main Line route.
PLEASE READ THE FULL PRODUCT DESCRIPTION BELOW
OO Gauge SET E16-1 - product code 4WH0901601
This set E16-1 includes parts to construct One (1) detailed Type A Structure with Slope Top Masts that has a span to cater for up to 2 (two) tracks.
Two Mast Bases are included in the kit, with four magnets to fit into the bases and OHLE structure. The use of magnets allows the OHLE structures to be easily removed and re-fitted on your layout.
PLEASE NOTE - the registration arms are NOT included and should be purchased separately.
Registration Arm and Catenary Wire Supports for the Type A Structure available to Purchase Separately are as follows:-
• SET E16-6 - Two Single Registration Arms and two Catenary Wire Supports (magnetic type to allow fitting of Peco type OHL wires) note [wires are not included] - Product code 4WH0901606
All parts are supplied unpainted on sprues. Preparation and assembly with glue is required. Before painting it is recommended to apply a light coat of primer. Instructions are available on-line or paper copy by special request only at the time of ordering. Glue and paint is not included.
Regarding the spacing of OHLE masts, the real railway mast spacing can be vary between about 20metres and 70metres which equates to 260 to 920mm in OO Gauge. In general mast spacing is likely to be closer together at junctions and on sharper curves.
The Peco wires are available in the following lengths 200mm, 260mm, 340mm, 380mm and 500mm, so if you are fitting wires then it makes sense to space your masts to suit the Peco wire lengths. [wires are not included in this kit]
OHLE Structure kit (SET E16-1) dimensions:-
• Overall height above baseboard (including bases) - 111mm
• Overall length of structure (across the tracks) - 155mm
• Nominal Span distance between inner edge of Bases - 130mm
• Overall width of structure - 14mm
• Nominal height of contact wire (if fitted to Magnetic Registration Arms) - 78mm above baseboard [wires not included]
Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment Structure Kit – Mk1 25kV Type B Lattice Mast Structure 2-Track structure,Typical of a type fitted to the West Coast Main Line route, including Magnetic Bases.PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWOO Gauge SET E16-11 - product code 4WH0901611Detailed Overhead Line Equipment Structure Kit – Mk1 25kV Type B Lattice Mast Structure 2-Track structure, including Magnetic Bases, typical of a type fitted to the West Coast Main Line route.
PLEASE READ THE FULL PRODUCT DESCRIPTION BELOW
OO Gauge SET E16-11 - product code 4WH0901611
This set E16-11 includes parts to construct One (1) detailed Type B Structure with Lattice Masts that has a span to cater for up to 2 (two) tracks.
Two Mast Bases are included in the kit, with four magnets to fit into the bases and OHLE structure. The use of magnets allows the OHLE structures to be easily removed and re-fitted on your layout.
PLEASE NOTE - the registration arms are NOT included and should be purchased separately.
Registration Arm and Catenary Wire Supports for the Type B Structure available to Purchase Separately are as follows:-
• SET E16-6 - Two Single Registration Arms and two Catenary Wire Supports (magnetic type to allow fitting of Peco type OHL wires) note [wires are not included] - Product code 4WH0901606
All parts are supplied unpainted on sprues. Preparation and assembly with glue is required. Before painting it is recommended to apply a light coat of primer. Instructions are available on-line or paper copy by special request only at the time of ordering. Glue and paint is not included.
Regarding the spacing of OHLE masts, the real railway mast spacing can be vary between about 20metres and 70metres which equates to 260 to 920mm in OO Gauge. In general mast spacing is likely to be closer together at junctions and on sharper curves.
The Peco wires are available in the following lengths 200mm, 260mm, 340mm, 380mm and 500mm, so if you are fitting wires then it makes sense to space your masts to suit the Peco wire lengths. [wires are not included in this kit]
OHLE Structure kit (SET E16-11) dimensions:-
• Overall height above baseboard (including bases) - 111mm
• Overall length of structure (across the tracks) - 155mm
• Nominal Span distance between inner edge of Bases - 130mm
• Overall width of structure - 14mm
• Nominal height of contact wire (if fitted to Magnetic Registration Arms) - 78mm above baseboard [wires not included]
Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment Structure Kit – Mk1 25kV Type B Lattice Mast Structure 4-Track structure,Typical of a type fitted to the West Coast Main Line route, including Magnetic Bases.PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWOO Gauge SET E16-12 - product code 4WH0901612Detailed Overhead Line Equipment Structure Kit – Mk1 25kV Type B Lattice Mast Structure 4-Track structure, including Magnetic Bases, typical of a type fitted to the West Coast Main Line route.
PLEASE READ THE FULL PRODUCT DESCRIPTION BELOW
OO Gauge SET E16-12 - product code 4WH0901612
This set E16-12 includes parts to construct One (1) detailed Type B Structure with Lattice Masts that has a span to cater for up to 4 (four) tracks.
Two Mast Bases are included in the kit, with four magnets to fit into the bases and OHLE structure. The use of magnets allows the OHLE structures to be easily removed and re-fitted on your layout.
PLEASE NOTE - the registration arms are NOT included and should be purchased separately.
Registration Arm and Catenary Wire Supports for the Type B Structure available to Purchase Separately are as follows:-
• SET E16-6 - Two Single Registration Arms and two Catenary Wire Supports (magnetic type to allow fitting of Peco type OHL wires) note [wires are not included] - Product code 4WH0901606
All parts are supplied unpainted on sprues. Preparation and assembly with glue is required. Before painting it is recommended to apply a light coat of primer. Instructions are available on-line or paper copy by special request only at the time of ordering. Glue and paint is not included.
Regarding the spacing of OHLE masts, the real railway mast spacing can be vary between about 20metres and 70metres which equates to 260 to 920mm in OO Gauge. In general mast spacing is likely to be closer together at junctions and on sharper curves.
The Peco wires are available in the following lengths 200mm, 260mm, 340mm, 380mm and 500mm, so if you are fitting wires then it makes sense to space your masts to suit the Peco wire lengths. [wires are not included in this kit]
OHLE Structure kit (SET E16-12) dimensions:-
• Overall height above baseboard (including bases) - 111mm
• Overall length of structure (across the tracks) - 256mm
• Nominal Span distance between inner edge of Bases - 230mm
• Overall width of structure - 14mm
• Nominal height of contact wire (if fitted to Magnetic Registration Arms) - 78mm above baseboard [wires not included]
Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment Structure Kit – Mk1 25kV Type B Cantilever Lattice Mast Structure for 2-Tracks,Typical of a type fitted to the West Coast Main Line route, including Magnetic Base.PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWOO Gauge SET E16-15 - product code 4WH0901615Detailed Overhead Line Equipment Structure Kit – Mk1 25kV Type B Cantilever Lattice Mast Structure for up to 2-Tracks, including Magnetic Base, typical of a type fitted to the West Coast Main Line route.
PLEASE READ THE FULL PRODUCT DESCRIPTION BELOW
OO Gauge SET E16-15 - product code 4WH0901615
This set E16-15 includes parts to construct One (1) detailed Type B Cantilever Structure with a Lattice Mast that has a span to cater for up to 2 (two) tracks.
One Mast Base is included in the kit, with two magnets to fit into the base and OHLE structure. The use of magnets allows the OHLE structures to be easily removed and re-fitted on your layout.
PLEASE NOTE - the registration arms are NOT included and should be purchased separately.
Registration Arm and Catenary Wire Supports for the Type B Structure available to Purchase Separately are as follows:-
• SET E16-6 - Two Single Registration Arms and two Catenary Wire Supports (magnetic type to allow fitting of Peco type OHL wires) note [wires are not included] - Product code 4WH0901606
All parts are supplied unpainted on sprues. Preparation and assembly with glue is required. Before painting it is recommended to apply a light coat of primer. Instructions are available on-line or paper copy by special request only at the time of ordering. Glue and paint is not included.
Regarding the spacing of OHLE masts, the real railway mast spacing can be vary between about 20metres and 70metres which equates to 260 to 920mm in OO Gauge. In general mast spacing is likely to be closer together at junctions and on sharper curves.
The Peco wires are available in the following lengths 200mm, 260mm, 340mm, 380mm and 500mm, so if you are fitting wires then it makes sense to space your masts to suit the Peco wire lengths. [wires are not included in this kit]
OHLE Structure kit (SET E16-15) dimensions:-
• Overall height above baseboard (including bases) - 111mm
• Overall length of structure (across the tracks) - 115mm
• Overall width of structure - 14mm
• Nominal height of contact wire (if fitted to E16-6 Magnetic Registration Arms) - 78mm above baseboard [wires not included]
Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment Structure Kit – Mk1 25kV Type A Structure 4-Track structure,Typical of a type fitted to the West Coast Main Line route, incl. Magnetic Bases.PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWOO Gauge SET E16-2 - product code 4WH0901602Detailed Overhead Line Equipment Structure Kit – Mk1 25kV Type A Structure 4-Track structure, incl. Magnetic Bases, typical of a type fitted to the West Coast Main Line route.
PLEASE READ THE FULL PRODUCT DESCRIPTION BELOW
OO Gauge SET E16-2 - product code 4WH0901602
This set E16-2 includes parts to construct One (1) detailed Type A Structure with Slope Top Masts that has a span to cater for up to 4 (four) tracks.
Two Mast Bases are included in the kit, with four magnets to fit into the bases and OHLE structure. The use of magnets allows the OHLE structures to be easily removed and re-fitted on your layout.
PLEASE NOTE - the registration arms are NOT included and should be purchased separately.
Registration Arm and Catenary Wire Supports for the Type A Structure available to Purchase Separately are as follows:-
• SET E16-6 - Two Single Registration Arms and two Catenary Wire Supports (magnetic type to allow fitting of Peco type OHL wires) note [wires are not included] - Product code 4WH0901606
All parts are supplied unpainted on sprues. Preparation and assembly with glue is required. Before painting it is recommended to apply a light coat of primer. Instructions are available on-line or paper copy by special request only at the time of ordering. Glue and paint is not included.
Regarding the spacing of OHLE masts, the real railway mast spacing can be vary between about 20metres and 70metres which equates to 260 to 920mm in OO Gauge. In general mast spacing is likely to be closer together at junctions and on sharper curves.
The Peco wires are available in the following lengths 200mm, 260mm, 340mm, 380mm and 500mm, so if you are fitting wires then it makes sense to space your masts to suit the Peco wire lengths. [wires are not included in this kit]
OHLE Structure kit (SET E16-2) dimensions:-
• Overall height above baseboard (including bases) - 111mm
• Overall length of structure (across the tracks) - 260mm
• Nominal Span distance between inner edge of Bases - 230mm
• Overall width of structure - 14mm
• Nominal height of contact wire (if fitted to Magnetic Registration Arms) - 78mm above baseboard [wires not included]
Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment Structure Kit – Mk1 25kV Type C Platform Structure with Tall Masts, 2-Track structure,Typical of a type fitted to the West Coast Main Line route, including Magnetic Bases.PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWOO Gauge SET E16-23 - product code 4WH0901623Detailed Overhead Line Equipment Structure Kit – Mk1 25kV Type C Platform Structure with Tall Masts, 2-Track structure, incl. Magnetic Bases, typical of a type fitted to the West Coast Main Line route.PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWOO Gauge SET E16-23 - product code 4WH0901623This set E16-23 includes parts to construct One (1) detailed Type C Platform Structure with Tall Masts that has a span to cater for up to 2 (two) tracks. Two Mast Bases are included in the kit, with four magnets to fit into the bases and OHLE structure. The use of magnets allows the OHLE structures to be easily removed and re-fitted on your layout.PLEASE NOTE - the registration arms are NOT included and should be purchased separately.Registration Arm and Catenary Wire Supports for the Type C Structure available to Purchase Separately are as follows:-• SET E16-26 - Two Single Registration Arms and two Catenary Wire Supports (magnetic type to allow fitting of Peco type OHL wires) note [wires are not included] - Product code 4WH0901626All parts are supplied unpainted on sprues. Preparation and assembly with glue is required. Before painting it is recommended to apply a light coat of primer. Instructions are available on-line or paper copy by special request only at the time of ordering. Glue and paint is not included.Regarding the spacing of OHLE masts, the real railway mast spacing can be vary between about 20metres and 70metres which equates to 260 to 920mm in OO Gauge. In general mast spacing is likely to be closer together at junctions and on sharper curves.The Peco wires are available in the following lengths 200mm, 260mm, 340mm, 380mm and 500mm, so if you are fitting wires then it makes sense to space your masts to suit the Peco wire lengths. [wires are not included in this kit]OHLE Structure kit (SET E16-23) assembled dimensions:-• Overall height above your platform (including bases) - 101mm• Overall length of structure (across the tracks) - 221mm• Nominal Span distance between inner edge of Bases - 190mm• Overall width of structure - 14mm• Nominal height of contact wire (if fitted to Magnetic Registration Arms) - 78mm above baseboard [wires not included], this is assuming a nominal 18mm Platform height.Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment Structure Kit – Mk1 25kV Type C Platform Double Sided Tall Mast, for use with E16-23 platform structure kits,Typical of a type fitted to the West Coast Main Line route, including Magnetic Base.PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWOO Gauge SET E16-24 - product code 4WH0901624Detailed Overhead Line Equipment Structure Kit – Mk1 25kV Type C Platform Double Sided Tall Mast, including a Magnetic Base, typical of a type fitted to the West Coast Main Line route.
PLEASE READ THE FULL PRODUCT DESCRIPTION BELOW
OO Gauge SET E16-24 - product code 4WH0901624
This set E16-24 includes parts to construct One (1) detailed Type C Platform Double Sided Tall Mast that is designed to fit between two E16-23 Platform Structure kits (not included), to allow spanning of multiple platforms.
One Mast Base is included in the kit, with two magnets to fit into the base and OHLE structure. The use of magnets allows the OHLE structures to be easily removed and re-fitted on your layout.
All parts are supplied unpainted on sprues. Preparation and assembly with glue is required. Before painting it is recommended to apply a light coat of primer. Instructions are available on-line or paper copy by special request only at the time of ordering. Glue and paint is not included.
OHLE Structure kit (SET E16-24) assembled dimensions:-
• Overall height above your platform (including bases) - 101mm
• Overall length of mast (across the tracks) - 30mm
• Overall width of structure - 14mm
• Nominal height of contact wire (if fitted to Magnetic Registration Arms) - 78mm above baseboard [wires not included], this is assuming a nominal 18mm Platform height.
Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment Mk1 OHLE 2 x Combined Registration Arms / Catenary Wire Supports (magnetic type) for fitting to Mk1 Type C structure kits.PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWOO Gauge SET E16-26 - product code 4WH0901626Detailed Overhead Line Equipment Mk1 OHLE 2 x Combined Type C Registration Arms / Catenary Wire Supports (magnetic type) for fitting to our Mk1 Type C structure kits.
PLEASE READ THE FULL PRODUCT DESCRIPTION BELOW
OO Gauge SET E16-26 - product code 4WH0901626
This set E16-26 includes parts designed specifically to fit to our Mk1 Type C OHLE kits E16-21, E16-22 and E16-23 (not included).
The Registration Arms / Catenary Wire Supports may be fitted either way round underneath the OHLE structure span.
The kit consists of:-
- Two (2) Combined Registration Arms & Catenary Wire Supports, under-span mount (magnetic type)
- Six (6) Magnets (4 + 2 spare) for fitting into the registration arms and catenary wire supports which will allow fitting of Peco type OHL wires. Note - the Peco wires are not included.
All parts are supplied unpainted on sprues. Preparation and assembly with glue is required. Before painting it is recommended to apply a light coat of primer. Instructions are available on-line or paper copy by special request only at the time of ordering. Glue and paint is not included.
Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment Structure Kit – Mk1 25kV Type D Low Mast Structure 2-Track structure,Typical of a type fitted to the West Coast Main Line route, including Magnetic Bases.PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWOO Gauge SET E16-31 - product code 4WH0901631Detailed Overhead Line Equipment Structure Kit – Mk1 25kV Type D Low Mast Structure 2-Track structure, including Magnetic Bases, typical of a type fitted to the West Coast Main Line route.
PLEASE READ THE FULL PRODUCT DESCRIPTION BELOW
OO Gauge SET E16-31 - product code 4WH0901631
This set E16-31 includes parts to construct One (1) detailed Type D Structure with Low Height Masts that has a span to cater for up to 2 (two) tracks.
The slightly lower height structure typical of the southern section of the West Coast Main Line allows the fitting of the catenary wire supports above the structure.
Two Mast Bases are included in the kit, with four magnets to fit into the bases and OHLE structure. The use of magnets allows the OHLE structures to be easily removed and re-fitted on your layout.
PLEASE NOTE - the registration arms are NOT included and should be purchased separately.
Registration Arm and Catenary Wire Supports for the Type D Structure available to Purchase Separately are as follows:-
• SET E16-36 - Two Single Registration Arms and two Catenary Wire Supports (magnetic type to allow fitting of Peco type OHL wires) note [wires are not included] - Product code 4WH0901636
All parts are supplied unpainted on sprues. Preparation and assembly with glue is required. Before painting it is recommended to apply a light coat of primer. Instructions are available on-line or paper copy by special request only at the time of ordering. Glue and paint is not included.
Regarding the spacing of OHLE masts, the real railway mast spacing can be vary between about 20metres and 70metres which equates to 260 to 920mm in OO Gauge. In general mast spacing is likely to be closer together at junctions and on sharper curves.
The Peco wires are available in the following lengths 200mm, 260mm, 340mm, 380mm and 500mm, so if you are fitting wires then it makes sense to space your masts to suit the Peco wire lengths. [wires are not included in this kit]
OHLE Structure kit (SET E16-31) dimensions:-
• Overall height above baseboard (including bases) - 100mm
• Overall length of structure (across the tracks) - 155mm
• Nominal Span distance between inner edge of Bases - 130mm
• Overall width of structure - 14mm
• Nominal height of contact wire (if fitted to Magnetic Registration Arms) - 78mm above baseboard [wires not included]
Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment Structure Kit – Mk1 25kV Type D Platform Structure with Low Masts, 2-Track structure,Typical of a type fitted to the West Coast Main Line route, including Magnetic Bases.PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWOO Gauge SET E16-33 - product code 4WH0901633Detailed Overhead Line Equipment Structure Kit – Mk1 25kV Type D Platform Structure with Low Masts, 2-Track structure, incl. Magnetic Bases, typical of a type fitted to the West Coast Main Line route.
PLEASE READ THE FULL PRODUCT DESCRIPTION BELOW
OO Gauge SET E16-33 - product code 4WH0901633
This set E16-33 includes parts to construct One (1) detailed Type D Platform Structure with Low Masts that has a span to cater for up to 2 (two) tracks.
Two Mast Bases are included in the kit, with four magnets to fit into the bases and OHLE structure. The use of magnets allows the OHLE structures to be easily removed and re-fitted on your layout.
The slightly lower height structure typical of the southern section of the West Coast Main Line allows the fitting of the catenary wire supports above the structure.
PLEASE NOTE - the registration arms are NOT included and should be purchased separately.
Registration Arm and Catenary Wire Supports for the Type D Structure available to Purchase Separately are as follows:-
• SET E16-36 - Two Single Registration Arms and two Catenary Wire Supports (magnetic type to allow fitting of Peco type OHL wires) note [wires are not included] - Product code 4WH0901636
All parts are supplied unpainted on sprues. Preparation and assembly with glue is required. Before painting it is recommended to apply a light coat of primer. Instructions are available on-line or paper copy by special request only at the time of ordering. Glue and paint is not included.
Regarding the spacing of OHLE masts, the real railway mast spacing can be vary between about 20metres and 70metres which equates to 260 to 920mm in OO Gauge. In general mast spacing is likely to be closer together at junctions and on sharper curves.
The Peco wires are available in the following lengths 200mm, 260mm, 340mm, 380mm and 500mm, so if you are fitting wires then it makes sense to space your masts to suit the Peco wire lengths. [wires are not included in this kit]
OHLE Structure kit (SET E16-33) assembled dimensions:-
• Overall height above your platform (including bases) - 82mm
• Overall length of structure (across the tracks) - 221mm
• Nominal Span distance between inner edge of Bases - 190mm
• Overall width of structure - 14mm
• Nominal height of contact wire (if fitted to Magnetic Registration Arms) - 78mm above baseboard [wires not included], this is assuming a nominal 18mm Platform height.
Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment Structure Kit – Mk1 25kV Type D Platform Double Sided Low Mast, for use with E16-33 platform structure kits,Typical of a type fitted to the West Coast Main Line route, including Magnetic Base.PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWOO Gauge SET E16-34 - product code 4WH0901634Detailed Overhead Line Equipment Structure Kit – Mk1 25kV Type D Platform Double Sided Low Mast, including a Magnetic Base, typical of a type fitted to the West Coast Main Line route.
PLEASE READ THE FULL PRODUCT DESCRIPTION BELOW
OO Gauge SET E16-34 - product code 4WH0901634
This set E16-34 includes parts to construct One (1) detailed Type D Platform Double Sided Low Mast that is designed to fit between two E16-33 Platform Structure kits (not included), to allow spanning of multiple platforms.
One Mast Base is included in the kit, with two magnets to fit into the base and OHLE structure. The use of magnets allows the OHLE structures to be easily removed and re-fitted on your layout.
All parts are supplied unpainted on sprues. Preparation and assembly with glue is required. Before painting it is recommended to apply a light coat of primer. Instructions are available on-line or paper copy by special request only at the time of ordering. Glue and paint is not included.
OHLE Structure kit (SET E16-34) assembled dimensions:-
• Overall height above your platform (including bases) - 82mm
• Overall length of mast (across the tracks) - 40mm
• Overall width of structure - 14mm
• Nominal height of contact wire (if fitted to Magnetic Registration Arms) - 78mm above baseboard [wires not included], this is assuming a nominal 18mm Platform height.
Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment Mk1 OHLE 2 x Type D Registration Arms and 2 x Catenary Wire Supports (magnetic type) for fitting to Mk1 Type D structure kits.PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWOO Gauge SET E16-36 - product code 4WH0901636Detailed Overhead Line Equipment Mk1 OHLE 2 x Type D Registration Arms and 2 x Catenary Wire Supports (magnetic type) for fitting to Mk1 Type D structure kits.
PLEASE READ THE FULL PRODUCT DESCRIPTION BELOW
OO Gauge SET E16-36 - product code 4WH0901636
This set E16-36 includes parts designed specifically to fit to our Mk1 Type D OHLE kits E16-31, E16-32 and E16-33 (not included).
The Registration Arms and Catenary Wire Supports may be fitted either way round to either side/top of the OHLE structure span.
The kit consists of:-
- Two (2) Single Side Mount Type Registration Arms (magnetic type)
- Two (2) Catenary Wire Top Mount Supports (magnetic type)
- Six (6) Magnets (4 + 2 spare) for fitting into the registration arms and catenary wire supports which will allow fitting of Peco type OHL wires. Note - the Peco wires are not included.
All parts are supplied unpainted on sprues. Preparation and assembly with glue is required. Before painting it is recommended to apply a light coat of primer. Instructions are available on-line or paper copy by special request only at the time of ordering. Glue and paint is not included.
Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment Mk1 OHLE 6 x Type D Return Conductor Wire Supports for fitting to Mk1 Type D structure kits.PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWOO Gauge SET E16-37 - product code 4WH0901637Detailed Overhead Line Equipment Mk1 OHLE 6 x Type D Return Conductor Wire Supports for fitting to Mk1 Type D structure kits.
PLEASE READ THE FULL PRODUCT DESCRIPTION BELOW
OO Gauge SET E16-37 - product code 4WH0901637
This set E16-37 includes parts designed specifically to fit to our Mk1 Type D OHLE kits E16-31, E16-32 and E16-33 (not included).The Return Conductor Wire Supports may be fitted either way round to either side of the OHLE structure span.
The kit consists of:-
- Two (2) Single Side Mount Return Conductor Supports
- Two (2) Double Side Mount Return Conductor Supports
- Two (2) Single Structure End Mount Return Conductor Supports
All parts are supplied unpainted on sprues. Preparation and assembly with glue is required. Before painting it is recommended to apply a light coat of primer. Instructions are available on-line or paper copy by special request only at the time of ordering. Glue and paint is not included.
Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment Structure Kit – Mk1 25kV Type E Viaduct Structure kit, (110mm)Typical of a type fitted to the West Coast Main Line routeIncl. Special Viaduct Side Mount Magnetic BasesPLEASE READ THE FULL PRODUCT DESCRIPTION BELOWOO Gauge SET E16-51 - product code 4WH0901651Detailed Overhead Line Equipment Structure Kit – Mk1 25kV Type E Viaduct Structure for your 110mm wide viaduct, incl. Special Viaduct Side Mount Magnetic Bases, typical of a type fitted to the West Coast Main Line route.
PLEASE READ THE FULL PRODUCT DESCRIPTION BELOW
OO Gauge SET E16-51 - product code 4WH0901651
This set E16-51 includes parts to construct One (1) detailed Type E Viaduct Structure with Two Masts that has a span to cater for 2-track Viaduct Structures of 110mm width.
Two Viaduct Mast Side Mount Bases are included in the kit, with four magnets to fit into the bases and OHLE structure. The use of magnets allows the OHLE structures to be easily removed and re-fitted on your layout.
PLEASE NOTE - the registration arms are NOT included and should be purchased separately.
Registration Arm and Catenary Wire Supports for the Type E Structure available to Purchase Separately are as follows:-
• SET E16-56 - Two Single Registration Arms and two Catenary Wire Supports (magnetic type to allow fitting of Peco type OHL wires) note [wires are not included] - Product code 4WH0901656
All parts are supplied unpainted on sprues. Preparation and assembly with glue is required. Before painting it is recommended to apply a light coat of primer. Instructions are available on-line or paper copy by special request only at the time of ordering. Glue and paint is not included.
Regarding the spacing of OHLE masts, the real railway mast spacing can be vary between about 20metres and 70metres which equates to 260 to 920mm in OO Gauge. In general mast spacing is likely to be closer together at junctions and on sharper curves.
The Peco wires are available in the following lengths 200mm, 260mm, 340mm, 380mm and 500mm, so if you are fitting wires then it makes sense to space your masts to suit the Peco wire lengths. [wires are not included in this kit]
OHLE Structure kit (SET E16-51) dimensions:-
• Overall height of structure (including bases) - 124mm
• Overall length of structure (across the tracks) - 122mm
• Nominal Span distance between inner edge of Bases - 110mm
• Overall width of structure - 8.5mm
• Nominal height of contact wire (if fitted to Magnetic Registration Arms) - 78mm above baseboard [wires not included]
Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment Structure Kit – Mk1 25kV Type E Viaduct Structure kit (145mm),Typical of a type fitted to the West Coast Main Line routeIncl. Special Viaduct Side Mount Magnetic BasesPLEASE READ THE FULL PRODUCT DESCRIPTION BELOWOO Gauge SET E16-52 - product code 4WH0901652Detailed Overhead Line Equipment Structure Kit – Mk1 25kV Type E Viaduct Structure for your 145mm wide viaduct, incl. Special Viaduct Side Mount Magnetic Bases, typical of a type fitted to the West Coast Main Line route.
PLEASE READ THE FULL PRODUCT DESCRIPTION BELOW
OO Gauge SET E16-52 - product code 4WH0901652
This set E16-52 includes parts to construct One (1) detailed Type E Viaduct Structure with Two Masts that has a span to cater for 2-track Viaduct Structures of 145mm width.
Two Viaduct Mast Side Mount Bases are included in the kit, with four magnets to fit into the bases and OHLE structure. The use of magnets allows the OHLE structures to be easily removed and re-fitted on your layout.
PLEASE NOTE - the registration arms are NOT included and should be purchased separately.
Registration Arm and Catenary Wire Supports for the Type E Structure available to Purchase Separately are as follows:-
• SET E16-56 - Two Single Registration Arms and two Catenary Wire Supports (magnetic type to allow fitting of Peco type OHL wires) note [wires are not included] - Product code 4WH0901656
All parts are supplied unpainted on sprues. Preparation and assembly with glue is required. Before painting it is recommended to apply a light coat of primer. Instructions are available on-line or paper copy by special request only at the time of ordering. Glue and paint is not included.
OHLE Structure kit (SET E16-54) dimensions:-
• Overall height of structure (including bases) - 124mm
• Overall length of structure (across the tracks) - 158mm
• Nominal Span distance between inner edge of Bases - 145mm
• Overall width of structure - 8.5mm
• Nominal height of contact wire (if fitted to Magnetic Registration Arms) - 78mm above baseboard [wires not included]
Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment Mk1 OHLE 1 x Type E Double Registration Arm and 2 x Catenary Wire Supports (magnetic type) for fitting to Mk1 Type E structure kits.PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWOO Gauge SET E16-56 - product code 4WH0901656Detailed Overhead Line Equipment Mk1 OHLE 1 x Type E Double Registration Arm and 2 x Catenary Wire Supports (magnetic type) for fitting to Mk1 Type E structure kits.
PLEASE READ THE FULL PRODUCT DESCRIPTION BELOW
OO Gauge SET E16-56 - product code 4WH0901656
This set E16-56 includes parts designed specifically to fit to our Mk1 Type E OHLE kits E16-51 and E16-52 (not included).
The Registration Arms and Catenary Wire Supports may be fitted either way round to either side of the OHLE structure span.
The kit consists of:-
- One (1) Doublle Side Mount Type Registration Arm (magnetic type)
- Two (2) Catenary Wire Side Mount Supports (magnetic type)
- Six (6) Magnets (4 + 2 spare) for fitting into the registration arms and catenary wire supports which will allow fitting of Peco type OHL wires. Note - the Peco wires are not included.
All parts are supplied unpainted on sprues. Preparation and assembly with glue is required. Before painting it is recommended to apply a light coat of primer. Instructions are available on-line or paper copy by special request only at the time of ordering. Glue and paint is not included.
Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment Mk1 OHLE 2 x Type A Registration Arms and 2 x Catenary Wire Supports (magnetic type) for fitting to Mk1 Type A and Type B structure kits.PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWOO Gauge SET E16-6 - product code 4WH0901606Detailed Overhead Line Equipment Mk1 OHLE 2 x Type A Registration Arms and 2 x Catenary Wire Supports (magnetic type) for fitting to Mk1 Type A and Type B structure kits.
PLEASE READ THE FULL PRODUCT DESCRIPTION BELOW
OO Gauge SET E16-6 - product code 4WH0901606
This set E16-6 includes parts designed specifically to fit to our Mk1 Type A and Type B OHLE kits E16-1, E16-2, E16-11 and E16-12 (not included).Note, this set will also fit to our Mk1 Type E OHLE Viaduct kits E16-51 and E16-52 (not included).
The Registration Arms and Catenary Wire Supports may be fitted either way round to either side of the OHLE structure span.
The kit consists of:-
- Two (2) Single Side Mount Type Registration Arms (magnetic type)
- Two (2) Catenary Wire Side Mount Supports (magnetic type)
- Six (6) Magnets (4 + 2 spare) for fitting into the registration arms and catenary wire supports which will allow fitting of Peco type OHL wires. Note - the Peco wires are not included.
All parts are supplied unpainted on sprues. Preparation and assembly with glue is required. Before painting it is recommended to apply a light coat of primer. Instructions are available on-line or paper copy by special request only at the time of ordering. Glue and paint is not included.
Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment Structure Kit – Mk1 25kV Type F Anchor Portal 4-Track structure,Typical of a type fitted to the West Coast Main Line route, incl. Magnetic Bases.PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWOO Gauge SET E16-61 - product code 4WH0901661Detailed Overhead Line Equipment Structure Kit – Mk1 25kV Type F Anchor Portal 4-Track structure, including Magnetic Bases, typical of a type fitted to the West Coast Main Line route.
PLEASE READ THE FULL PRODUCT DESCRIPTION BELOW
OO Gauge SET E16-61 - product code 4WH0901661
This set E16-61 includes parts to construct One (1) detailed Type F Anchor Portal 4-Track structure with Double Frame Masts that has a span to cater for up to 4 (four) tracks.
Four Mast Bases are included in the kit, with four magnets to fit into two of the bases and OHLE structure. The use of magnets allows the OHLE structures to be easily removed and re-fitted on your layout.
PLEASE NOTE - the registration arms are NOT included and should be purchased separately.
Registration Arms and Wire Anchors for the Type F Structure available to Purchase Separately are as follows:-
• SET E16-66 - Registration Arms and Wire Anchors Set (magnetic type to allow fitting of Peco type OHL wires) note [wires are not included] - Product code 4WH0901666
All parts are supplied unpainted on sprues. Preparation and assembly with glue is required. Before painting it is recommended to apply a light coat of primer. Instructions are available on-line or paper copy by special request only at the time of ordering. Glue and paint is not included.
Regarding the spacing of OHLE masts, the real railway mast spacing can be vary between about 20metres and 70metres which equates to 260 to 920mm in OO Gauge. In general mast spacing is likely to be closer together at junctions and on sharper curves.
The Peco wires are available in the following lengths 200mm, 260mm, 340mm, 380mm and 500mm, so if you are fitting wires then it makes sense to space your masts to suit the Peco wire lengths. [wires are not included in this kit]
OHLE Structure kit (SET E16-61) dimensions:-
• Overall height above baseboard (including bases) - 105mm
• Overall length of structure (across the tracks) - 256mm
• Nominal Span distance between inner edge of Bases - 230mm
• Overall width of structure - 44mm
• Nominal height of contact wire (if fitted to Magnetic Registration Arms) - 78mm above baseboard [wires not included]
Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment Mk1 OHLE 4 x Type F Registration Arms and 8 x Wire Anchors (magnetic type) for fitting to Mk1 Type F Anchor Portal structure kits.PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWOO Gauge SET E16-66 - product code 4WH0901666Detailed Overhead Line Equipment Mk1 OHLE 4 x Type F Registration Arms and 8 x Wire Anchors (magnetic type) for fitting to Mk1 Type F Anchor Portal structure kits.
PLEASE READ THE FULL PRODUCT DESCRIPTION BELOW
OO Gauge SET E16-66 - product code 4WH0901666
This set E16-66 includes parts designed specifically to fit to our Mk1 Type F OHLE Anchor Portal kits E16-61 and E16-62 (not included).
The Registration Arms may be fitted either way round to either side of the OHLE structure span. The Wire Anchors may be fitted to either side of the upper or lower frame of the OHLE structure span. Please refer to the pictures and the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
The kit consists of:-
- Four (4) Single Side Mount Type Registration Arms (magnetic type)
- Eight (8) Wire Anchors (magnetic type)
- Twelve (12) Magnets for fitting into the registration arms and catenary wire supports which will allow fitting of Peco type OHL wires. Note - the Peco wires are not included.
All parts are supplied unpainted on sprues. Preparation and assembly with glue is required. Before painting it is recommended to apply a light coat of primer. Instructions are available on-line or paper copy by special request only at the time of ordering. Glue and paint is not included.
Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment Mk1 OHLE Type F 100mm Span Extension for fitting to Mk1 Type F Anchor Portal structure kits.
PLEASE READ THE FULL PRODUCT DESCRIPTION BELOW
OO Gauge SET E16-67 - product code 4WH0901667Detailed Overhead Line Equipment Mk1 OHLE 1 x Type F 100mm Span Extension for fitting to Mk1 Type F Anchor Portal structure kits.
PLEASE READ THE FULL PRODUCT DESCRIPTION BELOW
OO Gauge SET E16-67 - product code 4WH0901667
This set E16-67 includes parts designed specifically to fit to our Mk1 Type F OHLE kits E16-61 and E16-62 (not included)
This extension span is designed to be fitted during assembly of the structure kit.
The kit consists of:-
- One (1) 100mm Span Extension (Type F)
All parts are supplied unpainted on sprues. Preparation and assembly with glue is required. Before painting it is recommended to apply a light coat of primer. Instructions are available on-line or paper copy by special request only at the time of ordering. Glue and paint is not included.
Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment Mk1 OHLE 6 x Type A Return Conductor Wire Supports for fitting to Mk1 Type A, B, C and E structure kits.PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWOO Gauge SET E16-7 - product code 4WH0901607Detailed Overhead Line Equipment Mk1 OHLE 6 x Type A Return Conductor Wire Supports for fitting to Mk1 Type A, B, C and E structure kits.
PLEASE READ THE FULL PRODUCT DESCRIPTION BELOW
OO Gauge SET E16-7 - product code 4WH0901607
This set E16-7 includes parts designed specifically to fit to our Mk1 Type A, Type B, Type C and Type E OHLE kits E16-1, E16-2, E16-11 and E16-12, E16-23, E16-51 and E16-52 (not included).The Return Conductor Wire Supports may be fitted either way round to either side of the OHLE structure span.
The kit consists of:-
- Two (2) Single Side Mount Return Conductor Supports
- Two (2) Double Side Mount Return Conductor Supports
- Two (2) Single Structure End Mount Return Conductor Supports
All parts are supplied unpainted on sprues. Preparation and assembly with glue is required. Before painting it is recommended to apply a light coat of primer. Instructions are available on-line or paper copy by special request only at the time of ordering. Glue and paint is not included.
Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment Structure Kit – Mk1 25kV Type G, I-Beam Mast Structure 2-Track structure,Typical of a type fitted to the West Coast Main Line route, including Magnetic Bases.PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWOO Gauge SET E16-71 - product code 4WH0901671Detailed Overhead Line Equipment Structure Kit – Mk1 25kV Type G, I-Beam Mast Structure 2-Track structure, including Magnetic Bases, typical of a type fitted to the West Coast Main Line route.
PLEASE READ THE FULL PRODUCT DESCRIPTION BELOW
OO Gauge SET E16-71 - product code 4WH0901671
This set E16-71 includes parts to construct One (1) detailed Type G Structure with I-Beam Masts that has an I-Beam span to cater for up to 2 (two) tracks.
Two Mast Bases are included in the kit, with four magnets to fit into the bases and OHLE structure. The use of magnets allows the OHLE structures to be easily removed and re-fitted on your layout.
PLEASE NOTE - the registration arms are NOT included and should be purchased separately.
Registration Arm and Catenary Wire Supports for the Type B Structure available to Purchase Separately are as follows:-
• SET E16-76 - Two Single Registration Arms and two Catenary Wire Supports (magnetic type to allow fitting of Peco type OHL wires) note [wires are not included] - Product code 4WH0901676
All parts are supplied unpainted on sprues. Preparation and assembly with glue is required. Before painting it is recommended to apply a light coat of primer. Instructions are available on-line or paper copy by special request only at the time of ordering. Glue and paint is not included.
Regarding the spacing of OHLE masts, the real railway mast spacing can be vary between about 20metres and 70metres which equates to 260 to 920mm in OO Gauge. In general mast spacing is likely to be closer together at junctions and on sharper curves.
The Peco wires are available in the following lengths 200mm, 260mm, 340mm, 380mm and 500mm, so if you are fitting wires then it makes sense to space your masts to suit the Peco wire lengths. [wires are not included in this kit]
OHLE Structure kit (SET E16-71) dimensions:-
• Overall height above baseboard (including bases) - 116mm
• Overall length of structure (across the tracks) - 195mm
• Nominal Span distance between inner edge of Bases - 170mm
• Overall width of structure - 14mm
• Nominal height of contact wire (if fitted to Magnetic Registration Arms) - 78mm above baseboard [wires not included]
Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment Mk1 OHLE 2 x Type G Combined Registration Arms / Catenary Wire Supports (magnetic type) for fitting to Mk1 Type G, I-Beam structure kits.PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWOO Gauge SET E16-76 - product code 4WH0901676Detailed Overhead Line Equipment Mk1 OHLE 2 x Type G Combined Registration Arms / Catenary Wire Supports (magnetic type) for fitting to Mk1 Type G, I-Beam structure kits.
PLEASE READ THE FULL PRODUCT DESCRIPTION BELOW
OO Gauge SET E16-76 - product code 4WH0901676
This set E16-76 includes parts designed specifically to fit to our Mk1 Type G, I-Beam OHLE kit E16-71 (not included).
The Combined Registration Arms / Catenary Wire Supports may be fitted either way round underneath the OHLE structure span.
The kit consists of:-
- Two (2) Combined Registration Arms / Catenary Wire Mount Supports (magnetic type)
- Six (6) Magnets (4 + 2 spare) for fitting into the registration arms and catenary wire supports which will allow fitting of Peco type OHL wires. Note - the Peco wires are not included.
All parts are supplied unpainted on sprues. Preparation and assembly with glue is required. Before painting it is recommended to apply a light coat of primer. Instructions are available on-line or paper copy by special request only at the time of ordering. Glue and paint is not included.
Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment Mk1 OHLE Type G 2 x 100mm Span Extension for fitting to Mk1 Type G, I-Beam structure kits.
PLEASE READ THE FULL PRODUCT DESCRIPTION BELOW
OO Gauge SET E16-77 - product code 4WH0901677Detailed Overhead Line Equipment Mk1 OHLE 2 x Type G 100mm Span Extension for fitting to Mk1 Type G, I-Beam structure kits.
PLEASE READ THE FULL PRODUCT DESCRIPTION BELOW
OO Gauge SET E16-77 - product code 4WH0901677
This set E16-77 includes parts designed specifically to fit to our Mk1 Type G OHLE kit E16-71 (not included)
This extension spans are designed to be fitted during assembly of the structure kit.
The kit consists of:-
- Two (2) 100mm I-Beam Span Extensions (Type G)
All parts are supplied unpainted on sprues. Preparation and assembly with glue is required. Before painting it is recommended to apply a light coat of primer. Instructions are available on-line or paper copy by special request only at the time of ordering. Glue and paint is not included.
Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment Mk1 OHLE Type A 100mm Span Extension for fitting to Mk1 Type A, B, C and E structure kits.
PLEASE READ THE FULL PRODUCT DESCRIPTION BELOW
OO Gauge SET E16-8 - product code 4WH0901608Detailed Overhead Line Equipment Mk1 OHLE 1 x Type A 100mm Span Extension for fitting to Mk1 Type A, B, C and E structure kits.
PLEASE READ THE FULL PRODUCT DESCRIPTION BELOW
OO Gauge SET E16-8 - product code 4WH0901608
This set E16-8 includes parts designed specifically to fit to our Mk1 Type A, Type B, Type C and Type E OHLE kits E16-1, E16-2, E16-11 and E16-12, E16-23, E16-51 and E16-52 (not included)
This extension span is designed to be fitted during assembly of the structure kit.
The kit consists of:-
- One (1) 100mm Span Extension (Type A)
All parts are supplied unpainted on sprues. Preparation and assembly with glue is required. Before painting it is recommended to apply a light coat of primer. Instructions are available on-line or paper copy by special request only at the time of ordering. Glue and paint is not included.
Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment Mast Structure KitSERIES 1 - Single Insulated Cantilever (SIC) Inner type with registration arm, including Magnetic BaseOO GaugeSET E3-1 - product code 4WH0900301PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWDetailed Overhead Line Equipment Mast Structure Kit - SERIES 1 - Single Insulated Cantilever (SIC) Inner type with registration arm, including Magnetic BasePLEASE READ THE FULL PRODUCT DESCRIPTION BELOWOO Gauge SET E3-1 - product code 4WH0900301This set E3-1 includes parts to construct one (1) basic SERIES 1 - Single Insulated Cantilever (SIC) type Mast structure. One Pile Driven style Base is included in the kit with height spacers and magnets to fit into the base and OHLE structure. The use of magnets allows the OHLE structures to be easily removed and re-fitted on your layout.Also included is a mast spacer tool, this will help you position the mast the correct distance from the track.All parts are supplied unpainted; before painting it is recommended to apply a light coat of primer.Regarding the spacing of OHLE masts, the real railway mast spacing can be vary between about 20metres and 70metres which equates to 260 to 920mm in OO Gauge. In general mast spacing is likely to be closer together at junctions and on sharper curves.
OHLE Structure kit (SET E3-1) dimensions:-
Maximum height above baseboard (including base) - 108mm
Overall length of Inner type structure (across the track) - 76mm
Max width of structure/base - 14mm
Nominal height of contact wire (if fitted to Magnetic Registration Arms) - 78mm above baseboard [wires not included]
Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment 10 Mast Structures KitSERIES 1 - Single Insulated Cantilever (SIC) Outer type with registration arm, including Magnetic BasePack of 10 MastsOO GaugeSET E3-10 - product code 4WH0900310PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWDetailed Overhead Line Equipment Mast Structure Kit - SERIES 1 - Single Insulated Cantilever (SIC) Outer type with registration arm, including Magnetic BasePLEASE READ THE FULL PRODUCT DESCRIPTION BELOWOO Gauge SET E3-10 - product code 4WH0900310This set E3-10 includes parts to construct ten (10) basic SERIES 1 - Single Insulated Cantilever (SIC) type Mast structures. Ten Pile Driven style Bases are included in the kit with height spacers and magnets to fit into the base and OHLE structures. The use of magnets allows the OHLE structures to be easily removed and re-fitted on your layout.Also included is a mast spacer tool, this will help you position the mast the correct distance from the track.All parts are supplied unpainted; before painting it is recommended to apply a light coat of primer.Regarding the spacing of OHLE masts, the real railway mast spacing can be vary between about 20metres and 70metres which equates to 260 to 920mm in OO Gauge. In general mast spacing is likely to be closer together at junctions and on sharper curves.OHLE Structure kit (SET E3-10) mast dimensions:-Maximum height above baseboard (including base) - 108mmOverall length of Outer type structure (across the track) - 66mmMax width of structure/base - 14mmNominal height of contact wire (if fitted to Magnetic Registration Arms) - 78mm above baseboard [wires not included]Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment 10 Mast Structures Kit SERIES 1 - Single Insulated Cantilever (SIC) Inner type with MAGNETIC registration arm, including Magnetic BasePack of 10 MastsOO GaugeSET E3-11 - product code 4WH0900311PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWDetailed Overhead Line Equipment Mast Structure Kit - SERIES 1 - Single Insulated Cantilever (SIC) Inner type with MAGNETIC registration arm, including Magnetic BasePLEASE READ THE FULL PRODUCT DESCRIPTION BELOWOO Gauge SET E3-11 - product code 4WH0900311This set E3-11 includes parts to construct ten (10) basic SERIES 1 - Single Insulated Cantilever (SIC) Inner type Mast structures that have a MAGENTIC type Registration Arms. PLEASE NOTE that this kit includes Magnets to support the fitting of Peco type OHL contact wires, NOTE the contact wires are NOT included.PLEASE NOTE the Magnets will need to be fitted into the Registration ArmsTen Pile Driven style Bases are included in the kit with height spacers and magnets to fit into the base and OHLE structures. The use of magnets allows the OHLE structures to be easily removed and re-fitted on your layout.Also included is a mast spacer tool, this will help you position the mast the correct distance from the track.All parts are supplied unpainted; before painting it is recommended to apply a light coat of primer.Regarding the spacing of OHLE masts, the real railway mast spacing can be vary between about 20metres and 70metres which equates to 260 to 920mm in OO Gauge. In general mast spacing is likely to be closer together at junctions and on sharper curves.The Peco wires are available in the following lengths 200mm, 260mm, 340mm, 380mm and 500mm, so if you are fitting wires then it makes sense to space your masts to suit the Peco wire lengths. [wires are not included in this kit]
OHLE Structure kit (SET E3-11) mast dimensions:-
Maximum height above baseboard (including base) - 108mm
Overall length of Inner type structure (across the track) - 76mm
Max width of structure/base - 14mm
Nominal height of contact wire (if fitted to Magnetic Registration Arms) - 78mm above baseboard [wires not included]
Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment 10 Mast Structure KitSERIES 1 - Single Insulated Cantilever (SIC) Outer type with MAGNETIC registration arm, including Magnetic BasePack of 10 MastsOO GaugeSET E3-12 - product code 4WH0900312PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWDetailed Overhead Line Equipment Mast Structure Kit - SERIES 1 - Single Insulated Cantilever (SIC) Outer type with registration arm, including Magnetic BasePLEASE READ THE FULL PRODUCT DESCRIPTION BELOWOO Gauge SET E3-12 - product code 4WH0900312This set E3-12 includes parts to construct ten (10) basic SERIES 1 - Single Insulated Cantilever (SIC) type Mast structures that have MAGENTIC type Registration Arms. PLEASE NOTE that this kit includes Magnets to support the fitting of Peco type OHL contact wires, NOTE the contact wires are NOT included.PLEASE NOTE the Magnets will need to be fitted into the Registration ArmsTen Pile Driven style Bases are included in the kit with height spacers and magnets to fit into the base and OHLE structures. The use of magnets allows the OHLE structures to be easily removed and re-fitted on your layout.Also included is a mast spacer tool, this will help you position the mast the correct distance from the track.All parts are supplied unpainted; before painting it is recommended to apply a light coat of primer.Regarding the spacing of OHLE masts, the real railway mast spacing can be vary between about 20metres and 70metres which equates to 260 to 920mm in OO Gauge. In general mast spacing is likely to be closer together at junctions and on sharper curves.The Peco wires are available in the following lengths 200mm, 260mm, 340mm, 380mm and 500mm, so if you are fitting wires then it makes sense to space your masts to suit the Peco wire lengths. [wires are not included in this kit]OHLE Structure kit (SET E3-12) mast dimensions:-Maximum height above baseboard (including base) - 108mmOverall length of Outer type structure (across the track) - 66mmMax width of structure/base - 14mmNominal height of contact wire (if fitted to Magnetic Registration Arms) - 78mm above baseboard [wires not included]Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment Mast Structure KitSERIES 1 - Single Insulated Cantilever (SIC) Outer type with registration arm, including Magnetic BaseOO GaugeSET E3-2 - product code 4WH0900302PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWDetailed Overhead Line Equipment Mast Structure Kit - SERIES 1 - Single Insulated Cantilever (SIC) Outer type with registration arm, including Magnetic BasePLEASE READ THE FULL PRODUCT DESCRIPTION BELOWOO Gauge SET E3-2 - product code 4WH0900302This set E3-2 includes parts to construct one (1) basic SERIES 1 - Single Insulated Cantilever (SIC) type Mast structure. One Pile Driven style Base is included in the kit with height spacers and magnets to fit into the base and OHLE structure. The use of magnets allows the OHLE structures to be easily removed and re-fitted on your layout.Also included is a mast spacer tool, this will help you position the mast the correct distance from the track.All parts are supplied unpainted; before painting it is recommended to apply a light coat of primer.Regarding the spacing of OHLE masts, the real railway mast spacing can be vary between about 20metres and 70metres which equates to 260 to 920mm in OO Gauge. In general mast spacing is likely to be closer together at junctions and on sharper curves.OHLE Structure kit (SET E3-2) dimensions:-Maximum height above baseboard (including base) - 108mmOverall length of Outer type structure (across the track) - 66mmMax width of structure/base - 14mmNominal height of contact wire (if fitted to Magnetic Registration Arms) - 78mm above baseboard [wires not included]Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment Mast Structure KitSERIES 1 - Single Insulated Cantilever (SIC) Inner type with MAGNETIC registration arm, including Magnetic BaseOO GaugeSET E3-3 - product code 4WH0900303PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWDetailed Overhead Line Equipment Mast Structure Kit - SERIES 1 - Single Insulated Cantilever (SIC) Inner type with MAGNETIC registration arm, including Magnetic BasePLEASE READ THE FULL PRODUCT DESCRIPTION BELOWOO Gauge SET E3-3 - product code 4WH0900303This set E3-3 includes parts to construct one (1) basic SERIES 1 - Single Insulated Cantilever (SIC) Inner type Mast structure that has a MAGENTIC type Registration Arm. PLEASE NOTE that this kit includes Magnets to support the fitting of Peco type OHL contact wires, NOTE the contact wires are NOT included.PLEASE NOTE the Magnets will need to be fitted into the Registration ArmsOne Pile Driven style Base is included in the kit with height spacers and magnets to fit into the base and OHLE structure. The use of magnets allows the OHLE structures to be easily removed and re-fitted on your layout.Also included is a mast spacer tool, this will help you position the mast the correct distance from the track.All parts are supplied unpainted; before painting it is recommended to apply a light coat of primer.Regarding the spacing of OHLE masts, the real railway mast spacing can be vary between about 20metres and 70metres which equates to 260 to 920mm in OO Gauge. In general mast spacing is likely to be closer together at junctions and on sharper curves.The Peco wires are available in the following lengths 200mm, 260mm, 340mm, 380mm and 500mm, so if you are fitting wires then it makes sense to space your masts to suit the Peco wire lengths. [wires are not included in this kit]
OHLE Structure kit (SET E3-3) dimensions:-
Maximum height above baseboard (including base) - 108mm
Overall length of Inner type structure (across the track) - 76mm
Max width of structure/base - 14mm
Nominal height of contact wire (if fitted to Magnetic Registration Arms) - 78mm above baseboard [wires not included]
Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment Mast Structure KitSERIES 1 - Single Insulated Cantilever (SIC) Outer type with MAGNETIC registration arm, including Magnetic BaseOO GaugeSET E3-4 - product code 4WH0900304PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWDetailed Overhead Line Equipment Mast Structure Kit - SERIES 1 - Single Insulated Cantilever (SIC) Outer type with registration arm, including Magnetic BasePLEASE READ THE FULL PRODUCT DESCRIPTION BELOWOO Gauge SET E3-4 - product code 4WH0900304This set E3-4 includes parts to construct one (1) basic SERIES 1 - Single Insulated Cantilever (SIC) type Mast structure that has a MAGENTIC type Registration Arm. PLEASE NOTE that this kit includes Magnets to support the fitting of Peco type OHL contact wires, NOTE the contact wires are NOT included.PLEASE NOTE the Magnets will need to be fitted into the Registration ArmsOne Pile Driven style Base is included in the kit with height spacers and magnets to fit into the base and OHLE structure. The use of magnets allows the OHLE structures to be easily removed and re-fitted on your layout.Also included is a mast spacer tool, this will help you position the mast the correct distance from the track.All parts are supplied unpainted; before painting it is recommended to apply a light coat of primer.Regarding the spacing of OHLE masts, the real railway mast spacing can be vary between about 20metres and 70metres which equates to 260 to 920mm in OO Gauge. In general mast spacing is likely to be closer together at junctions and on sharper curves.The Peco wires are available in the following lengths 200mm, 260mm, 340mm, 380mm and 500mm, so if you are fitting wires then it makes sense to space your masts to suit the Peco wire lengths. [wires are not included in this kit]OHLE Structure kit (SET E3-4) dimensions:-Maximum height above baseboard (including base) - 108mmOverall length of Outer type structure (across the track) - 66mmMax width of structure/base - 14mmNominal height of contact wire (if fitted to Magnetic Registration Arms) - 78mm above baseboard [wires not included]Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment 5 Mast Structures KitSERIES 1 - Single Insulated Cantilever (SIC) Inner type with registration arm, including Magnetic BasePack of 5 MastsOO GaugeSET E3-5 - product code 4WH0900305PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWDetailed Overhead Line Equipment Mast Structure Kit - SERIES 1 - Single Insulated Cantilever (SIC) Inner type with registration arm, including Magnetic BasePLEASE READ THE FULL PRODUCT DESCRIPTION BELOWOO Gauge SET E3-5 - product code 4WH0900305This set E3-5 includes parts to construct five (5) basic SERIES 1 - Single Insulated Cantilever (SIC) type Mast structures. Five Pile Driven style Bases are included in the kit with height spacers and magnets to fit into the base and OHLE structures. The use of magnets allows the OHLE structures to be easily removed and re-fitted on your layout.Also included is a mast spacer tool, this will help you position the mast the correct distance from the track.All parts are supplied unpainted; before painting it is recommended to apply a light coat of primer.Regarding the spacing of OHLE masts, the real railway mast spacing can be vary between about 20metres and 70metres which equates to 260 to 920mm in OO Gauge. In general mast spacing is likely to be closer together at junctions and on sharper curves.
OHLE Structure kit (SET E3-5) mast dimensions:-
Maximum height above baseboard (including base) - 108mm
Overall length of Inner type structure (across the track) - 76mm
Max width of structure/base - 14mm
Nominal height of contact wire (if fitted to Magnetic Registration Arms) - 78mm above baseboard [wires not included]
Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment 5 Mast Structures KitSERIES 1 - Single Insulated Cantilever (SIC) Outer type with registration arm, including Magnetic BasePack of 5 MastsOO GaugeSET E3-6 - product code 4WH0900306PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWDetailed Overhead Line Equipment Mast Structure Kit - SERIES 1 - Single Insulated Cantilever (SIC) Outer type with registration arm, including Magnetic BasePLEASE READ THE FULL PRODUCT DESCRIPTION BELOWOO Gauge SET E3-6 - product code 4WH0900306This set E3-6 includes parts to construct five (5) basic SERIES 1 - Single Insulated Cantilever (SIC) type Mast structures. Five Pile Driven style Bases are included in the kit with height spacers and magnets to fit into the base and OHLE structures. The use of magnets allows the OHLE structures to be easily removed and re-fitted on your layout.Also included is a mast spacer tool, this will help you position the mast the correct distance from the track.All parts are supplied unpainted; before painting it is recommended to apply a light coat of primer.Regarding the spacing of OHLE masts, the real railway mast spacing can be vary between about 20metres and 70metres which equates to 260 to 920mm in OO Gauge. In general mast spacing is likely to be closer together at junctions and on sharper curves.OHLE Structure kit (SET E3-6) mast dimensions:-Maximum height above baseboard (including base) - 108mmOverall length of Outer type structure (across the track) - 66mmMax width of structure/base - 14mmNominal height of contact wire (if fitted to Magnetic Registration Arms) - 78mm above baseboard [wires not included]Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment 5 Mast Structures Kit SERIES 1 - Single Insulated Cantilever (SIC) Inner type with MAGNETIC registration arm, including Magnetic BasePack of 5 MastsOO GaugeSET E3-7 - product code 4WH0900307PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWDetailed Overhead Line Equipment Mast Structure Kit - SERIES 1 - Single Insulated Cantilever (SIC) Inner type with MAGNETIC registration arm, including Magnetic BasePLEASE READ THE FULL PRODUCT DESCRIPTION BELOWOO Gauge SET E3-7 - product code 4WH0900307This set E3-7 includes parts to construct five (5) basic SERIES 1 - Single Insulated Cantilever (SIC) Inner type Mast structures that have a MAGENTIC type Registration Arms. PLEASE NOTE that this kit includes Magnets to support the fitting of Peco type OHL contact wires, NOTE the contact wires are NOT included.PLEASE NOTE the Magnets will need to be fitted into the Registration ArmsFive Pile Driven style Bases are included in the kit with height spacers and magnets to fit into the base and OHLE structures. The use of magnets allows the OHLE structures to be easily removed and re-fitted on your layout.Also included is a mast spacer tool, this will help you position the mast the correct distance from the track.All parts are supplied unpainted; before painting it is recommended to apply a light coat of primer.Regarding the spacing of OHLE masts, the real railway mast spacing can be vary between about 20metres and 70metres which equates to 260 to 920mm in OO Gauge. In general mast spacing is likely to be closer together at junctions and on sharper curves.The Peco wires are available in the following lengths 200mm, 260mm, 340mm, 380mm and 500mm, so if you are fitting wires then it makes sense to space your masts to suit the Peco wire lengths. [wires are not included in this kit]
OHLE Structure kit (SET E3-7) mast dimensions:-
Maximum height above baseboard (including base) - 108mm
Overall length of Inner type structure (across the track) - 76mm
Max width of structure/base - 14mm
Nominal height of contact wire (if fitted to Magnetic Registration Arms) - 78mm above baseboard [wires not included]
Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment 5 Mast Structure KitSERIES 1 - Single Insulated Cantilever (SIC) Outer type with MAGNETIC registration arm, including Magnetic BasePack of 5 MastsOO GaugeSET E3-8 - product code 4WH0900308PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWDetailed Overhead Line Equipment Mast Structure Kit - SERIES 1 - Single Insulated Cantilever (SIC) Outer type with registration arm, including Magnetic BasePLEASE READ THE FULL PRODUCT DESCRIPTION BELOWOO Gauge SET E3-8 - product code 4WH0900308This set E3-8 includes parts to construct five (5) basic SERIES 1 - Single Insulated Cantilever (SIC) type Mast structures that have MAGENTIC type Registration Arms. PLEASE NOTE that this kit includes Magnets to support the fitting of Peco type OHL contact wires, NOTE the contact wires are NOT included.PLEASE NOTE the Magnets will need to be fitted into the Registration ArmsFive Pile Driven style Bases are included in the kit with height spacers and magnets to fit into the base and OHLE structures. The use of magnets allows the OHLE structures to be easily removed and re-fitted on your layout.Also included is a mast spacer tool, this will help you position the mast the correct distance from the track.All parts are supplied unpainted; before painting it is recommended to apply a light coat of primer.Regarding the spacing of OHLE masts, the real railway mast spacing can be vary between about 20metres and 70metres which equates to 260 to 920mm in OO Gauge. In general mast spacing is likely to be closer together at junctions and on sharper curves.The Peco wires are available in the following lengths 200mm, 260mm, 340mm, 380mm and 500mm, so if you are fitting wires then it makes sense to space your masts to suit the Peco wire lengths. [wires are not included in this kit]OHLE Structure kit (SET E3-8) mast dimensions:-Maximum height above baseboard (including base) - 108mmOverall length of Outer type structure (across the track) - 66mmMax width of structure/base - 14mmNominal height of contact wire (if fitted to Magnetic Registration Arms) - 78mm above baseboard [wires not included]Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Overhead Line Equipment 10 Mast Structures KitSERIES 1 - Single Insulated Cantilever (SIC) Inner type with registration arm, including Magnetic BasePack of 10 MastsOO GaugeSET E3-9 - product code 4WH0900309PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWDetailed Overhead Line Equipment Mast Structure Kit - SERIES 1 - Single Insulated Cantilever (SIC) Inner type with registration arm, including Magnetic BasePLEASE READ THE FULL PRODUCT DESCRIPTION BELOWOO Gauge SET E3-9 - product code 4WH0900309This set E3-9 includes parts to construct ten (10) basic SERIES 1 - Single Insulated Cantilever (SIC) type Mast structures. Ten Pile Driven style Bases are included in the kit with height spacers and magnets to fit into the base and OHLE structures. The use of magnets allows the OHLE structures to be easily removed and re-fitted on your layout.Also included is a mast spacer tool, this will help you position the mast the correct distance from the track.All parts are supplied unpainted; before painting it is recommended to apply a light coat of primer.Regarding the spacing of OHLE masts, the real railway mast spacing can be vary between about 20metres and 70metres which equates to 260 to 920mm in OO Gauge. In general mast spacing is likely to be closer together at junctions and on sharper curves.
OHLE Structure kit (SET E3-9) mast dimensions:-
Maximum height above baseboard (including base) - 108mm
Overall length of Inner type structure (across the track) - 76mm
Max width of structure/base - 14mm
Nominal height of contact wire (if fitted to Magnetic Registration Arms) - 78mm above baseboard [wires not included]
Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed N-Gauge Overhead Line Equipment - Pack of 3 Mast Structures SERIES 1 - Single Insulated Cantilever Masts (SIC) with registration arms, including Magnetic BasesSET E9-1 - product code 4WH0900301PLEASE READ THE FULL PRODUCT DESCRIPTION BELOWDetailed N-Gauge Overhead Line Equipment Mast Structure Kit - Pack of 3 MastsSERIES 1 - Single Insulated Cantilever Masts (SIC) with registration arms, including Magnetic BasesPLEASE READ THE FULL PRODUCT DESCRIPTION BELOWN Gauge SET E9-1 - product code 2WH0900901This set E9-1 includes parts to construct three (3) basic SERIES 1 - Single Insulated Cantilever (SIC) type Mast structures. Three Pile Driven style Bases are included in the kit with magnets to fit into the bases and OHLE structures. The use of magnets allows the OHLE structures to be easily removed and re-fitted on your layout.All parts are supplied unpainted; before painting it is recommended to apply a light coat of primer.Regarding the spacing of OHLE masts, the real railway mast spacing can be vary between about 20metres and 70metres which equates to 130 to 470mm in N Gauge. In general mast spacing is likely to be closer together at junctions and on sharper curves.
OHLE Structure kit (SET E9-1) mast dimensions:-
Maximum height above baseboard (including base) - 62mm
Overall length of mast structure (across the track) - 35mm
Max width of structure/base - 7mm
Please see the downloadable "OHLE Equipment Product Guide" in the Attachments TAB above.
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Detailed Electric Type Pallet TrucksOO GaugePack of 2
Detailed Electric Type Pallet TrucksPack of 2OO GaugeManual operated electric powered type trucks for moving pallets around depots and workshopsUnpainted, ready to paint to suit your depot or workshop sceneEnamel paints are recommended
In Stock
Shipped By Royal Mail 48 Tracked Item Will be Dispatched Using Royal Mail 48 Hour Tracked Service From Dispatch Time
Electric Wall Socket Connection BoxesOO GaugePack of 8Electric Wall Socket Connection Boxes, typical of those used in many workshops, depots and industrial buildings.OO GaugePack of 8
Electrical cables can be added by using our Rubber Silicone Tubing, product 0WH0401401With conduit below each box which can be trimmed to desired height.Overall height of conduit and connection box is 16mmSupplied unpainted.
